| PURPOSES OF THIS MANUAL |
This manual is an introduction to the CYCLEMATIC model CP-27EVS FINISHING LATHE. If you thoroughly read, will get valuable information in the installation, operation and servicing of the CP-27EVS CYCLEMATIC MACHINES.
The manual can be used for reference, because it is necessary to make minor adjustment for maintenance personnel and operators that have dealings with the model CP-27EVS machine.
The model CP-27EVS machines is built of extreme ease and safety of operation, the finest manufacturing and used high quality materials with the proper care and use, you are ensured trouble-free, accurate and economical operations for the life of the machines. |
 TOP |
| LIFTING MACHINE |
Figure 1-Lifting Machine
|
| Lifting machine, arrange rope or cable as shown in figure 1, and check to see if the correct balance has been obtained. Then insert pads of soft cloth between the edges of the rope and machine. The net weight of this machine is approx 300 kgs (660 lbs). So the rope or cable must be rated at 500kgs (1100lbs) capacity. |
| TOP |
| A.) ELECTRICAL CONNECTIONS |
The CP-27EVS HIGH PERFORMANCE FINISHING LATHE is shipped completely wired and assembled, turn cam switch "A" (Figure 2) to the off position, then check motor voltage, loosen screws "B" (Figure 2), and open the switch case cover, connect the wires from the power source to the terminals (R.S.T.), and ground connection is made at the "C" (Figure 3) which is the electric switch case. Push "START" bottom "D" (Figure 4), turn cam switch "F" (Figure 5) to the forward position, the spindle should rotate counter clock wise. If the spindle does not turn in the correct direction, turn cam switch "A" (Figure 2) to "OFF" position, disconnect electric power source and inter changes any two leads until the turning direction is correct when the spindle is rotation correctly, secure switch case cover, turn cam switch "A" (Figure 2) to on position.
|
Figure 2-Electrical Case |
Figure 3-Control Unit
|
Figure 4-Start Bottom and Power Light
|
* CAUTION:
RUNNING THE MACHINE IN THE WRONG DIRECTION WILL RESULT IN DAMAGE TO THE SPINDLE SPEED CHANGE UNIT.
* CAUTION:
FILL WITH MOBIL VACTRA OIL NO.2 FOR THE LUBRICATION. |
| TOP |
| B.) LUBRICATION |
Proper lubrication supplied carefully, will maintain the life and performance of the machine for a long period. Therefore, lubricate the machine with a high quality lubricant.
|
FOR MODEL CP-27EVS EQUIPPED WITH ELECTRONIC
VARI-SPEED SYSTEM |
| TOP |
| C.) SETTING SPINDLE SPEEDS |
Push start button switch "D" (Figure 5) on outside of control unit. Release Emergency Switch "E" (Figure 6) turn cam switch "F" (Figure 6) to the forward or reverse position, turn cam switch "G" (Figure 6) to the right to increase speed and to the left to decrease speed.
|
Figure 5-Start Button Switch and Power Light |
Figure 6-Speed Control Box |
| TOP |
| D.) BELT ADJUSTMENT |
If belt snap into two piece just remove handle "H" (Figure 7) to the left side and remove belt, after put new belt in to the machine, pull handle "H" (Figure 7) to the right side and tight it.
|
Figure 7- Belt Adjustment |
Figure 8-Control Unit |
| TOP |
| E.) SPINDLE BRAKE |
Brake Control by "A" (Figure 8) inverter.
|
| TOP |
| F.) COMPOUND SLIDE |
The compound slide rest can be readily applied to the CYCLEMATIC HIGH PERFORMANCE FINISHING LATHE for screw feed precision turning, facing and boring operations. The large diameter feed screws are hardened and mounted on preloaded ball bearings. The feed screw dials are 2" in diameter. Both dials give direct readings in thousandths and are adjustable for zero settings.
|
 |
* X-Travel 114mm (4-1/2").
* Z-Travel 140mm (5-1/2"). |
| TOP |
| G.) DOUBLE TOOL CROSS SLIDE |
The double tool cross slide can be locked at any location on the bed. To relocate cross slide, first loosen clamp screw "S" (Figure 10), then move cross slide to required location on bed and relock clamp screw "S" (Figure 10).
Loosen eccentric lock axles "E" (Figure 11), to change location of tool posts on cross slide.
Move tool post along T-slot and tighten eccentric lock axles "E" (Figure 11), to relocate tool block in T-slot of tool post base loosen nut "N" (Figure 11). Tool holder blocks take standard 9.52mm (3/8" ) square tool bits, to adjust tool bits to spindle centerline, loosen clamp screw "C" (Figure 10) and turn adjusting screw "A" (Figure 10) to raise or lower cutting tool.
The lever feed handle "L' (Figure 11) can be adjusted to a more convenient operating position, loosen nut "M' (Figure 11) and tap shaft at same end with plastic hammer to loosen taper lock, hole handle required position and tighten nut "M" (Figure 11).
The cross slide travel is limited by adjustable stop screws "O" (Figure 11). To limit travel, loosen lock screw "P" (Figure 11) and turn screw "O" (Figure 11) to required stop location.
Remove screw "E" AND "Q" (Figure 11) move top slide toward operator with lever feed handle to full gear travel. Loosen nut "M" (Figure 11) and tap shaft at same end with plastic hammer to loosen taper lock of handle, Pull top slide off bottom slide, then clean top and bottom slide. Grease gear and lubricate mating dovetail slides with Vactra Oil No.2. To grease lever feed shaft needle bearings, remove nut and washer "M" (Figure 11), and tap shaft at same end with plastic hammer to loosen taper lock. Remove shaft and bearing liner to grease bearings.
* CAUTION:
THE DOUBLE TOOL CROSS SLIDE SHOULD BE CLEANED AND LUBRICATED EVERY THREE MONTHS. |
Figure 10-Double Tool Cross Slide Locked |
Figure 11-Double Cross Slide Adjustment |
| BACK |
